Recherche - Archive ouverte HAL Accéder directement au contenu

Filtrer vos résultats

38 résultats
Page :
triés par

Metallurgical aspects of material behaviour in cutting of aisi 1045

 Cedric Courbon , Tarek Mabrouki , Joel Rech , Denis Mazuyer , F. Perrard , et al.
Key Engineering Materials, 2013, 554-557, pp.2085-2092. ⟨10.4028/www.scientific.net/KEM.554-557.2085⟩
Article dans une revue hal-00966328v1
Image document

Vers une modélisation physique de la coupe des aciers spéciaux : intégration du comportement métallurgique et des phénomènes tribologiques et thermiques aux interfaces

 Cédric Courbon
Autre. Ecole Centrale de Lyon, 2011. Français. ⟨NNT : 2011ECDL0046⟩
Thèse tel-00713527v1
Image document

Near surface transformations of stainless steel cold spray and laser cladding deposits after turning and ball-burnishing

 C. Courbon , A. Sova , F. Valiorgue , H. Pascal , J. Sijobert , et al.
Surface and Coatings Technology, 2019, 371, pp.235-244. ⟨10.1016/j.surfcoat.2019.01.092⟩
Article dans une revue emse-02888162v1

Importance of the contact interface definition in the numerical simulation of tool wear in metal cutting

 A. Giovenco , C. Courbon , Frédéric Cabanettes , Joël Rech , U. Masciantonio , et al.
22nd International ESAFORM Conference on Material Forming, ESAFORM 2019, May 2019, Vitoria-Gasteiz, Spain. ⟨10.1063/1.5112615⟩
Communication dans un congrès hal-04092895v1
Image document

Impact of cutting tool wear on residual stresses induced during turning of a 15-5 PH stainless steel

 F. Clavier , F. Valiorgue , C. Courbon , M. Dumas , J. Rech , et al.
Procedia CIRP, 2020, 87, pp.107 - 112. ⟨10.1016/j.procir.2020.02.074⟩
Article dans une revue hal-03491065v1

Characterization of wear modes in orthogonal milling of 15-5PH stainless steel

 T. David , G. Methon , R. M'Saoubi , M. Girinon , Joël Rech , et al.
24th International ESAFORM Conference on Material Forming, ESAFORM 2021, Apr 2021, Online Conference, Unknown Region. ⟨10.25518/esaform21.908⟩
Communication dans un congrès hal-04092870v1

High temperature tribological behaviour of PVD coated tool steel and aluminium under dry and lubricated conditions

 Justine Decrozant-Triquenaux , Leonardo Pelcastre , Cédric Courbon , Braham Prakash , Jens Hardell
Friction, 2021, 9 (4), pp.802-821. ⟨10.1007/s40544-020-0435-7⟩
Article dans une revue hal-04084012v1

Further insight into the chip formation of ferritic-pearlitic steels: microstructural evolutions and associated thermo-mechanical loadings

 Cedric Courbon , Tarek Mabrouki , Joel Rech , Denis Mazuyer , F. Perrard , et al.
International Journal of Machine Tools and Manufacture, 2014, 77, pp.34 - 46. ⟨10.1016/j.ijmachtools.2013.10.010⟩
Article dans une revue hal-00938538v1

On the identification conditions of a constitutive model in machining of AISI 1045 steel

 C. Courbon , Tarek Mabrouki , Joël Rech , Jean Francois Rigal , Denis Mazuyer , et al.
ESAFORM2010, Apr 2010, BRESCIA, Italy. pp.CDRom
Communication dans un congrès hal-00504167v1

Towards a better definition of the mechanical and thermal interface behaviour in dry cutting simulation of AISI 1045 steel

 C. Courbon , Tarek Mabrouki , Joël Rech , Denis Mazuyer , E. d'Eramo , et al.
4th International conference on Tribology in Manufacturing Processes, Jun 2010, Nice, France. pp.CD ROM
Communication dans un congrès hal-00504197v1

Numerical analysis of the tribological and geometrical impacts of tool wear on the thermomechanical loadings induced by 15-5PH steel turning

 F. Clavier , Frédéric Valiorgue , C. Courbon , Joël Rech , A.V. Robaeys , et al.
18th CIRP Conference on Modeling of Machining Operations, CMMO 2021, Jun 2021, Ljubljana, Slovenia. pp.411-416, ⟨10.1016/j.procir.2021.09.070⟩
Communication dans un congrès hal-04092872v1

Effect of surface engineered tool steel and lubrication on aluminium transfer at high temperature

 Justine Decrozant-Triquenaux , Leonardo Pelcastre , Cédric Courbon , Braham Prakash , Jens Hardell
Wear, 2021, 477, ⟨10.1016/j.wear.2021.203879⟩
Article dans une revue hal-04084013v1

Experimental analysis of the impact of an artificially generated tool wear pattern on the residual stress induced by 15-5PH steel turning

 F. Clavier , Frédéric Valiorgue , C. Courbon , Joël Rech , H. Pascal , et al.
6th CIRP Conference on Surface Integrity, CSI 2022, Jun 2022, Lyon, France. pp.394-399, ⟨10.1016/j.procir.2022.04.075⟩
Communication dans un congrès hal-04092860v1

Tribological effect of lubricated liquid carbon dioxide on TiAl6V4 and AISI1045 under extreme contact conditions

 C. Courbon , L. Sterle , M. Cici , F. Pusavec
23rd International Conference on Material Forming, ESAFORM 2020, May 2020, Cottbus, Germany. pp.511-516, ⟨10.1016/j.promfg.2020.04.139⟩
Communication dans un congrès hal-04092889v1
Image document

The contribution of microstructure and friction in broaching Ferrite–Pearlite steels

 C. Courbon , I.M. Arrieta , F. Cabanettes , J. Rech , P.-J. Arrazola
CIRP Annals - Manufacturing Technology, 2020, 69, pp.57 - 60. ⟨10.1016/j.cirp.2020.04.023⟩
Article dans une revue hal-03491455v1
Image document

Finite deformations govern the anisotropic shear-induced area reduction of soft elastic contacts

 J. Lengiewicz , M. de Souza , M. A. Lahmar , C. Courbon , D. Dalmas , et al.
Journal of the Mechanics and Physics of Solids, 2020, 143, pp.104056. ⟨10.1016/j.jmps.2020.104056⟩
Article dans une revue hal-02562750v2

Development of a novel high temperature open tribometer with laser-based heating system

 T. Leveille , D. Fabre , Mehmet Cici , Julien Sijobert , M. Doubenskaia , et al.
Wear, 2021, 477, pp.203881. ⟨10.1016/j.wear.2021.203881⟩
Article dans une revue hal-04092575v1
Image document

Effect of sliding velocity on friction-induced microstructural evolution in Copper

 Grégoire Jacquet Jacquet , Guillaume Kermouche , Cédric Courbon , David Tumbajoy-Spinel , Joel Rech
6th International Conference on nanomaterials by severe plastic deformation (NANOSPD6), Jun 2014, Metz, France. ⟨10.1088/1757-899X/63/1/012039⟩
Communication dans un congrès emse-01527036v1

Determination of constitutive friction laws appropriate for simulation of cutting processes

 V. Schulze , F. Bleicher , C. Courbon , M. Gerstenmeyer , L. Meier , et al.
CIRP Journal of Manufacturing Science and Technology, 2022, 38, pp.139-158. ⟨10.1016/j.cirpj.2022.04.008⟩
Article dans une revue hal-04081513v1
Image document

Approche expérimentale et numérique de l'usinage assisté haute-pression

 Cédric Courbon , Davor Kramar , Joël Rech , Janez Kopac
CFM 2009 - 19ème Congrès Français de Mécanique, Aug 2009, Marseille, France
Communication dans un congrès hal-03391197v1
Image document

Étude des perturbations thermiques induites par des hétérogénéités de contact à l'interface outil-copeau en usinage

 Cédric Courbon , Tarek Mabrouki , Joël Rech , Denis Mazuyer , Enrico d'Eramo
CFM 2013 - 21ème Congrès Français de Mécanique, Aug 2013, Bordeaux, France
Communication dans un congrès hal-03440628v1
Image document

Mini symposium on cutting and machining: 25 years of ESAFORM activity

 Domenico Umbrello , Takashi Matsumura , Pedro J. Arrazola , Guenael Germain , Cédric Courbon
International Journal of Material Forming, 2022, 15 (3), ⟨10.1007/s12289-022-01680-w⟩
Article dans une revue hal-03684154v1
Image document

Towards the prediction of surface roughness induced by the belt finishing process: influence of the workmaterial on the roughness reduction rate

 F. Cabanettes , O. Cherguy , C. Courbon , A. Giovenco , S. Han , et al.
Procedia CIRP, 2020, 87, pp.210 - 215. ⟨10.1016/j.procir.2020.02.108⟩
Article dans une revue hal-03491066v1

A 3D modeling strategy to predict efficiently cutting tool wear in longitudinal turning of AISI 1045 steel

 C. Courbon , D. Fabre , G. Methon , A. Giovenco , Frédéric Cabanettes , et al.
CIRP Annals - Manufacturing Technology, 2021, 70 (1), pp.57-60. ⟨10.1016/j.cirp.2021.04.071⟩
Article dans une revue hal-04092576v1

Numerical modeling of wear in orthogonal cutting of multilayer coated tools

 G. Methon , C. Courbon , R. M'Saoubi , M. Girinon , Joël Rech
18th CIRP Conference on Modeling of Machining Operations, CMMO 2021, Jun 2021, Ljubljana, Slovenia. pp.67-72, ⟨10.1016/j.procir.2021.09.012⟩
Communication dans un congrès hal-04092874v1

Comparison of the CEL and ALE approaches for the simulation of orthogonal cutting of 15-5PH and 42CrMo4 materials

 Abderrahmen Aridhi , Thomas Perard , Frédéric Valiorgue , Cédric Courbon , Joël Rech , et al.
Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2022, ⟨10.1177/09544054221136390⟩
Article dans une revue hal-04083038v1

Local material removal mechanisms of cemented carbides in abrasive flow machining

 F. Salvatore , R. Chabord , C. Courbon , Bernard Beaugiraud , H. Hamdi
22nd International ESAFORM Conference on Material Forming, ESAFORM 2019, May 2019, Vitoria-Gasteiz, Spain. ⟨10.1063/1.5112647⟩
Communication dans un congrès hal-04092894v1

On the identification conditions of a constitutive model in machining of aisi 1045 steel

 Cedric Courbon , Tarek Mabrouki , Joel Rech , Jean-Francois Rigal , Denis Mazuyer , et al.
International Journal of Material Forming, 2010, 3, pp.439-442. ⟨10.1007/s12289-010-0801-5⟩
Article dans une revue hal-00951066v1
Image document

Finite element modelling and investigation of the interaction between an ultrasonic wave and a discontinuous interface

 Vipul Vijigiri , Cedric Courbon , Guillaume Kermouche , Juliette Cayer-Barrioz
44th LEEDS 2017, Sep 2017, Lyon, France
Communication dans un congrès hal-03633896v1

Numerical and Experimental Investigations in Orthogonal Milling of 15-5PH Stainless Steel

 G. Methon , C. Courbon , R. M'Saoubi , Mathieu Girinon , Joël Rech
25th International Conference on Material Forming, ESAFORM 2022, Apr 2022, Braga, Portugal. pp.1609-1618, ⟨10.4028/p-cqvqzr⟩
Communication dans un congrès hal-04092846v1
Page :